Menu Item/Description | Setting value (: Default) | ||
---|---|---|---|
01 Language Setting Select the language used in the touch panel and voice messages. | Language used in LCD: Japanese, Hangul Taiwan, Chinese English, French, German, Italian, Spanish
Language in Voice Message: English, Japanese, OFF | ||
02 Unit Setting Select the unit of measurement for numeric values to be displayed on the touch panel. | mm, Inch(Decimal Point), Inch(Fraction) | ||
03 Paper Tray Setting | |||
01 Paper Setting | |||
01 Paper Profile Setting Register or delete the paper settings. Up to 500 can be registered. | Paper Type, Profile Name, Paper Size, Weight, Colored Paper, Punch, Both Sides Adj., RU Curl Adj., Air Assist, Expert Adj., Curl Adjustment, Color Density Import, Export | ||
02 Preset Profile Management Allows you to add or delete a profile. | Search Condition of profile USB Import of Preset Profile, Delete, Add Profile Delete of Paper Profile | ||
02 Auto Tray Selection Setting Select the tray to take over the feeding when the tray currently used becomes out of paper. This function is called Auto Tray Switch (ATS). When selecting multiple trays for ATS, determine the priority of the trays. | ATS/APS Switch: Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11 Tray Priority: Order of priority for selected trays | ||
03 Type for Auto Paper Specify paper conditions that enable a tray to be selected in Auto Paper (APS). Paper conditions to be specified here are Paper Type, Weight, Punch, Tab Paper, and Colored Paper. | Paper Type: Plain, Fine, Coated, PrePrinted, Book/News, Plain-rough, Blank Insert, Textured Weight: 40-49g/m2/10-13 lb Bond, 50-54g/m2/14-15 lb Bond, 55-61g/m2/16-17 lb Bond, 62-74g/m2/18-19 lb Bond, 75-80g/m2/20-21 lb Bond, 81-91g/m2/22-24 lb Bond, 92-105g/m2/25-28 lb Bond, 106-135g/m2/29-36 lb Bond, 136-162g/m2/37-43 lb Bond, 163-216g/m2/44-57 lb Bond, 217-256g/m2/58-68 lb Bond, 257-300g/m2/69-81 lb Bond, 301-350g/m2/82-93 lb Bond Punch: Allow, Restrict Tab Paper: Allow, Restrict Colored Paper: White, Blue, Goldenrod, Gray, Green, Ivory, Orange, Pink, Red, Yellow, Cream, Clear White, Others, User Color | ||
04 Dehumidify Fan Heater Configure operation settings for the dehumidifying fan heater of Paper Feeder Unit (Tray 3 to Tray 11) and Large Capacity Post Inserter PI-PFU (PI-PFU1 to PI-PFU3). | Dryness Preparation: ON, OFF Fan Heater Control(Tray3), Fan Heater Control(Tray4), Fan Heater Control(Tray5), Fan Heater Control(Tray6), Fan Heater Control(Tray7), Fan Heater Control(Tray8), Fan Heater Control(Tray9), Fan Heater Control(Tray10), Fan Heater Control(Tray11), Fan Heater Control(Pi-PFU1), Fan Heater Control(Pi-PFU2), Fan Heater Control(Pi-PFU3): Auto, Compulsively ON, Compulsively OFF | ||
04 Reset Setting | |||
01 Auto Reset Setting The machine automatically restores the screen specified as the default screen after a certain period of inactivity. Select the time interval to activate this function. | OFF, 60 seconds, 120 seconds, 180 seconds, 240 seconds, 300 seconds, 360 seconds, 420 seconds, 480 seconds, 540 seconds | ||
05 Default Screen Setting Select the screen to be displayed when the sub power switch is turned on or Auto Reset is activated. | MACHINE, JOB LIST/Hold Job, JOB LIST/Reserved Job | ||
06 Power Save Setting | |||
01 Power Save Function Setting You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF. | Auto Low Power: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min. Auto Wake-up Cond.: All Jobs | ||
02 ErP Setting Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time. | Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours | ||
03 Main Power Auto OFF Setting Select whether to automatically turn OFF the main power switch after the sub power switch is turned OFF and the main body has completely cooled down. If turned ON, the above function is set. | ON, OFF | ||
07 Date/Time Setting Set the current date and time, the daylight-saving time, and the time difference. | Setting Time Daylight Saving Time: OFF, ON (1 to 150 min.) Time Zone: -12:00 to +13:00 (Default: +00:00) | ||
08 Operation/Info. Sound Setting | |||
01 Volume Setting Specify whether to turn the operation sound and speaker sound on or off, and also set the volume when they are turned on. | Operation Sound: ON, OFF, (Small) 1, 2, 3, 4, 5, 6, 7, 8 (Big) Speaker Sound: ON, OFF, (Small) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 (Big) | ||
02 Info. Sound Item Setting Specify each items provided for information sound and voice message. | Repeat Number Setting Info. Sound Repeat Number: 1 time, 2 times, 3 times Voice Repeat Number: 1 time, 2 times, 3 times Notice Set for Machine Stop Paper JAM: Voice, Info. Sound, OFF Paper Empty: Voice, Info. Sound, OFF Paper Differ: Voice, Info. Sound, OFF Replenish Toner: Voice, Info. Sound, OFF Service Call: Info. Sound, OFF Output Full: Info. Sound, OFF Other Notification Setting Job Complete Pre-notice: Voice, OFF Stop Button Acceptance: Voice, OFF Sample Print Completion: Voice, OFF Finisher Front Door Alert: Voice, OFF Other Info. Sound Setting For System Starting: Info. Sound, OFF For Sample Printing: Info. Sound, OFF For Print Job Receiving: Info. Sound, OFF | ||
09 Key Response Time Select the time interval to get the response from the machine when a key is pressed on the touch panel. | Normal, 0.5 seconds, 1 second, 2 seconds, 3 seconds | ||
10 Service Port Device Setting Specify whether or not to use a service port device, and select the keyboard type if the service port device is used. | Service Port Device: ON, OFF Keyboard Type: EN65, EN104, JP101, JP106 , JP109, UK, FR, IT, DE, ES | ||
11 Mouse Setting Select whether or not to use the Wheel Booster function and Cursor Auto Scrolling function, respectively, for when the mouse is connected. | Wheel Booster Setting: ON, OFF When using this function, set List Scroll Speed and Value Scroll Speed. Cursor Auto Scrolling Set.: ON, OFF When using this function, set Cursor Speed, Cancel Sensitivity, Prior Return Pos., and Prior Destination. |
Menu Item/Description | Setting value (: Default) |
---|---|
One Shot Message Indication Time Select the time span to display a shot message in the message area of the touch panel. | 3 seconds, 5 seconds |
Offset by Job Unit Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function. | ON, OFF (Selecting ON: Offset Job Number) |
Continuation Print Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break. | Printer ON, Printer OFF |
Dark Tone Control In order to adjust the quality of the output image, select whether to automatically decrease the output speed (Quality), prioritize the output speed, or disable the ability to control the tone. | OFF, Quality, Performance |
Icon Display for Dark Tone Control Select whether or not to display the Dark Tone icon while the Dark Tone Control function is enabled. This function is available only when Quality or Performance is selected at Dark Tone Control. | ON, OFF |
Dash Length(Page Stamp) Select the length of the dash to be used in a style of Page No. in Stamp. | Long, Short |
Center Crop Mark Trim Margin Specify the space between the center crop mark and image area (center crop mark trim margin). | 0.0 mm to 20.0 mm (Default: 1.0) |
Schedule Cross Axis Unit (Default) Select the unit of horizontal axis on the Schedule screen. | Timetable, Time Frame(m), Sheet Volume |
Hold Job Status after Output (Default) Select the default value to delete or save the data of hold job after outputting. | Delete, Save |
Hold Job Direct Output (Default) Select the default for the Direct Output check box under the Hold Job screen. ON selects the check box, and OFF clears the check box. | ON, OFF |
Offset Output Mode Specify how to offset the output sets. | Change Out Pos., Stop Print, Change Out Pos. + Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3), Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3) |
Needless Tab Paper Exit Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set. | ON, OFF |
Remaining Memory (Measurement Unit) Select the unit of displaying the remaining memory. | %, GB |
Remaining Memory (Warning) Select the percentage at which to give warning when the remaining memory is low. | 5% or Less, 10% or Less |
[Proof Copy] 1 Set/1st Sheet Selection If it is turned ON, the confirmation window is opened and you are asked to output one confirmation copy or to output only its first page when the Proof Copy is pressed. | ON, OFF |
Temp. Down/Up Control before Print Select whether to rotate the fusing roller before printing starts, in order to print at the appropriate temperature. | ON, OFF |
Both Sides Rotate/Skew If Disable is selected, the Rotate/Skew adjustment does not become available and does not function. | Enable, Disable |
Stop when Water Tank Near Empty Select whether to temporarily stop a job when the humidifier tank runs low on water. | Temporary Stop, Not Temporary Stop |
Auto Image Adjustment Deviation Check Select whether to automatically check a deviation. If you select ON, enter the specified value of a deviation. This option is displayed when Intelligent Quality Optimizer IQ-501 is mounted on the machine. | ON (ON: 0.5 mm to 10.0 mm), OFF |
Operation after Deviation Detected Select an operation to be performed when a deviation is detected. When Continue Output is selected, specify the paper tray to feed partition paper and the number of detection times. This option is displayed when Intelligent Quality Optimizer IQ-501 is mounted on the machine. | Stop, Continue Output, Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11), Detection Count (2 to 10 times) |
Select Chart Type (Auto Image Adj.) Select an automatic image adjustment chart for each paper weight. The unit of weight can be switched. This option is displayed when Intelligent Quality Optimizer IQ-501 is mounted on the machine. | 40-49g/m2/10-13 lb Bond: Type1, Type2 50-54g/m2/14-15 lb Bond: Type1, Type2 55-61g/m2/16-17 lb Bond: Type1, Type2 62-74g/m2/18-19 lb Bond: Type1, Type2 75-80g/m2/20-21 lb Bond: Type1, Type2 81-91g/m2/22-24 lb Bond: Type1, Type2 92-105g/m2/25-28 lb Bond: Type1, Type2 106-135g/m2/29-36 lb Bond: Type1, Type2 136-162g/m2/37-43 lb Bond: Type1, Type2 163-216g/m2/44-57 lb Bond: Type1, Type2 217-256g/m2/58-68 lb Bond: Type1, Type2 257-300g/m2/69-81 lb Bond: Type1, Type2 301-350g/m2/82-93 lb Bond: Type1, Type2 Change Unit |
Menu Item/Description | Setting value (: Default) |
---|---|
01 Outline Process Select the Outline Process for printing. | Text Thinning: Weak+, Weak, Normal, Strong, Strong+ Halftone Text Enhancement: Weak+, Normal, Strong+ FD Lead Edge Density Adjustment: -5, -4, -3, -2, -1, 0 FD Rear Edge Density Adjustment: 0, +1, +2, +3, +4, +5 |
02 Select Prior Output Tray Select the output tray for the jobs for which the output tray is specified as "Auto". This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532. | Main Tray, Sub Tray |
Change the user password previously registered with user authentication. This function is available when user authentication is enabled.
Menu Item/Description | Setting value (: Default) |
---|---|
01 Tandem Machine One Time Data Read Set the Partner MFP to receive all the data transmitted from This MFP before starting to print. | ON, OFF |
02 Tandem Machine Wait/Proof Set whether to transmit the data to the Partner MFP when This MFP starts scanning the data for proof copying. | Allow, Restrict |
03 Distribution Recovery Set the tandem-connected machines to perform the job distribution again for print quantity remaining on one machine when the other has already finished with its assignment. | ON, OFF |
04 Tandem IP Address Setting Specify the IP address of the Partner MFP. | IPv4 Address |
Menu Item/Description | Setting value (: Default) | |||||
---|---|---|---|---|---|---|
01 Power Save Setting | ||||||
01 Power Save Function Setting You can also select the condition of Auto Wake-up to activate the machine when a print job is received during Auto Shut OFF. | Auto Low Power: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min. Auto Shut OFF: --- min., 0.5 min., 3 min., 5 min., 10 min., 15 min., 30 min., 60 min., 90 min., 120 min., 240 min. Power Save Function: Auto Low Power, Auto Shut OFF Auto Wake-up Cond.: All Jobs | |||||
02 ErP Setting Automatically turn off the main power switch when the sub power switch is turned off, or when Auto Shut OFF or Auto Low Power has been active for a certain time. | Do Not Switch, 12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, 72 Hours | |||||
03 Main Power Auto OFF Setting Select whether to automatically turn OFF the main power switch after the sub power switch is turned OFF and the main body has completely cooled down. If turned ON, the above function is set. | ON, OFF | |||||
02 Date/Time Setting Set the current date and time, the daylight-saving time, and the time difference. | Setting Time Daylight Saving Time: OFF, ON (1 to 150 min.) Time Zone: -12:00 to +13:00 (Default: +00:00) | |||||
03 Weekly Timer Setting | ||||||
01 Weekly Timer ON/OFF Setting Specify whether or not to use the Weekly Timer function. | Weekly Timer ON, Weekly Timer OFF | |||||
02 Time Setting Set the ON/OFF times in hours and minutes. | ― | |||||
03 Date Setting Set the ON/OFF condition of the machine for a given day of a given month. | ― | |||||
04 Select Time for Power Save Set the machine to turn off and then on during the lunch break. | ON, OFF | |||||
05 Password Non-Business Hours Set a password to use the machine by turning on the power temporarily while the machine is in off condition due to the Weekly Timer function. | Default password: 0000 (4 digits) | |||||
04 Restrict User Access | ||||||
01 Function Usage Restriction Specify whether or not to allow the use of various functions. | Sample Print: Allow, Restrict USB Direct Print: Allow, Restrict | |||||
05 Expert Adjustment | ||||||
01 Printer Adjustment | ||||||
01 Restart Timing Adjustment Adjust the image position of lead edge in paper feed direction in the printer engine. Prerequisite: FD-Mag. Adjustment is completed. | Objects of adjustment: Side1: All Trays Offset Adj. Range: -45~+45 1 step = 0.1 mm Side1, Side2: Restart Timing (Tray1), Restart Timing (Tray2), Restart Timing (Tray3), Restart Timing (Tray4), Restart Timing (Tray5), Restart Timing (Tray6), Restart Timing (Tray7), Restart Timing (Tray8), Restart Timing (Tray9), Restart Timing (Tray10), Restart Timing (Tray11) Adj. Range: -30~+30 1 step = 0.1 mm [-] Lower [+] Higher | |||||
02 Centering Adjustment Adjust the image position in the crosswise direction of the printer engine. Prerequisite: CD-Mag. Adjustment is completed. | Adj. Range: -64~+63 1 step = 0.1 mm [-] Front [+] Back | |||||
03 FD-Mag. Adjustment Adjust the magnification in paper feed direction in the printer engine. | Objects of adjustment: Side1: Printer FD-Mag. Adj. Range: -10~+10 1 step = 0.05 % Objects of adjustment: Side2: Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11 Adj. Range: -10~0 1 step = 0.05 % [-] Short [+] Long | |||||
04 CD-Mag. Adjustment Adjust the magnification in crosswise direction in the printer engine. | Objects of adjustment: Side1: Printer CD-Mag. Adj. Range: -10~+10 1 step = 0.05 % Objects of adjustment: Side2: Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11 Adj. Range: -10~0 1 step = 0.05 % [-] Short [+] Long | |||||
05 Registration Loop Adj. Adjust the paper loop amount in registration roller section. | Objects of adjustment: Side1 Adj. Range: -7~+10 1 step = 1.0 mm Objects of adjustment: Side1 Thick Adj. Range: 0~+10 1 step = 1.0 mm Objects of adjustment: Side1 Thin Adj. Range: -6~+10 1 step = 1.0 mm Objects of adjustment: Side2, Side2 Thick, Side2 Thin Adj. Range: -10~+10 1 step = 1.0 mm [-] Short [+] Long | |||||
06 Pre-registration Adj. Adjust the paper loop amount in pre-registration roller section of the trays. | Objects of adjustment: Not Thin Paper, Thin Paper Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11 Adj. Range: -10~+10 1 step = 1.0 mm [-] Short [+] Long | |||||
07 Print Job JAM Setting Set whether or not to stop the machine as a paper jam when a mis-centering is detected. Select whether to display a message when the machine stops due to a paper jam or double feeding. | Mis-centering JAM Setting: Detect, Not Detect JAM Identification Display: Display, Not Display | |||||
02 Finisher Adjustment (Finisher FS-532) This menu item is to be displayed and allowed on the machine mounted with Finisher FS-532. | ||||||
01 Staple Finisher Adjustment | ||||||
01 Staple Finisher(Main) Adj. | ||||||
01 Exit Guide Paper Width Adj. Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven in straight delivery. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8.5 14 short edge feed, 8 13 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Wide [+] Narrow | |||||
02 Upper Gripper Operation Select the upper gripper operation for main tray outlet. | Auto, ON, OFF | |||||
03 Output Alignment Operation Select operation for output alignment. | Auto, ON, OFF | |||||
04 Staple Paper Width Adj. Adjust the board alignment width of the staples in the staple finisher. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] Wide [+] Narrow | |||||
05 FD Alignment Plate Adj. Adjust the vertical alignment fitting for staples in the staple finisher. | Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed, Custom(139~230 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Wide [+] Narrow | |||||
06 Staple Position Adjustment Adjust 2 position staple pitch and corner staple positions in staple finisher. | Objects of adjustment: 2 Position Pitch(120 mm), 2 Position Pitch(140 mm), 2 Position Pitch(165 mm), Rear Diagonal Adj. Range: -5~+5 1 step = 1 mm Objects of adjustment: Rear Parallel, Front Parallel Adj. Range: -3~+3 1 step = 1 mm [-] Narrow [+] Wide | |||||
07 Rewind Paddle Descent Adj. Adjust rewind paddle descent. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -10~+10 1 step = 0.2 mm [-] Little [+] Much | |||||
08 Rewind Function Operation Select the rewind paddle operation. | Auto, ON, OFF | |||||
02 Staple Finisher(Fold) Adj. This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510. | ||||||
01 Fold&Staple Paper Width Adj. Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded sheets show misalignment. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Narrow [+] Wide | |||||
02 Fold&Staple Pitch Adjustment Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -300~+300 1 step = 0.1 mm Staple pitch: [-] Narrow [+] Wide | |||||
03 Fold&Staple Fold Position Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm Upper output side: [-] Extend [+] Shorten | |||||
04 Fold&Staple Staple Position Adjust staple position in Saddle Stitcher SD-510. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm Upper output side: [-] Extend [+] Shorten | |||||
05 Half-Fold Fold Position Adj. Adjust half-fold position of fold function in Saddle Stitcher SD-510. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm Upper output side: [-] Extend [+] Shorten | |||||
06 Tri-Fold Adjustment | ||||||
01 Tri-Fold Position Adjustment Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510. Make this adjustment if each fold position for tri-folding is not within the allowance range. | Objects of adjustment: 8.5 11 short edge feed, A4 short edge feed, 16K short edge feed Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: [-] Extend [+] Shorten Fold 2: [-] Shorten [+] Extend | |||||
02 Double Fold Plate Adjustment Adjust double fold plate in saddle stitcher. Deepen in case of wide shift in bunch of the Fold 2. | Objects of adjustment: 8.5 11 short edge feed, A4 short edge feed, 16K short edge feed Adj. Range: -50~+50 1 step = 0.1 mm Quantity of inserting double fold plate: [-] Shallow [+] Deep | |||||
07 Half-Fold Strength Adj. To adjust the opening of booklets, increase the roller pressure time. * You cannot adjust the strength to fold booklets. * Long pressure time causes reduced productivity. | Adj. Range: 0~+10 1 step = 1 sec. | |||||
03 Staple Finisher(Punch) Adj. This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522. | ||||||
01 Registration Adjustment If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller. | Adj. Range: -50~+50 1 step = 0.1 mm [-] Short [+] Long | |||||
02 Horizontal Position Adj.(FD) Adjust the distance between the edge of the printed paper and the center of punch holes. | Objects of adjustment: Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm Punch position at paper edge: [-] Far [+] Close | |||||
03 Vertical Position Adj.(CD) Adjust the misalignment in center positions of paper and punch holes for each paper size. | Objects of adjustment: Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm Punch position: [-] Forward [+] Backward | |||||
04 Staple Finisher(PI) Adj. This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502. | ||||||
01 PI Registration Adjustment When paper fed from the Upper Tray or Lower Tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller. | Objects of adjustment: PI Upper Tray, PI Lower Tray Adj. Range: -5~+5 1 step = 1.0 mm [-] Short [+] Long | |||||
02 Finisher Adjustment (Output Tray OT-510) This menu item is displayed and can be set on the machine mounted with Output Tray OT-510. | ||||||
01 Staple Finisher Adjustment 01 Staple Finisher(Main)Adj. | ||||||
01 Exit Guide Paper Width Adj. Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven in straight delivery. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Wide [+] Narrow | |||||
02 Upper Gripper Operation Select the upper gripper operation for main tray delivery exit. | Auto, ON, OFF | |||||
03 Output Alignment Operation Select operation for output alignment. | Auto, ON, OFF | |||||
02 Finisher Adjustment (Folding Unit FD-503) This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503. | ||||||
02 Multi Folder Adjustment | ||||||
01 Multi Folder(Punch)Adj. | ||||||
01 Paper Width Adjustment Adjust the misalignment of punch hole positions. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, B5 short edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the randomness [+] To reduce the tilts | |||||
02 Punch Vertical Position Adj. | ||||||
01 2-Hole Punch Adjust the vertical position of punch holes made by the folding unit. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, A4 long edge feed, B5 short edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed Adj. Range: -40~+40 1 step = 0.1 mm [-] To move to the center [+] To move to the edge | |||||
02 3-Hole Punch Adjust the vertical position of punch holes made by the folding unit. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed Adj. Range: -40~+40 1 step = 0.1 mm [-] To move to the center [+] To move to the edge | |||||
02 4-Hole Punch Adjust the vertical position of punch holes made by the folding unit. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed Adj. Range: -40~+40 1 step = 0.1 mm [-] To move to the center [+] To move to the edge | |||||
02 Multi Folder(Fold)Adj. | ||||||
01 Half-Fold Position Adj. Adjust the folded position for half-fold. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To shorten the top face [+] To lengthen the top face | |||||
02 Z-Fold Position Adj. Adjust the fold positions for Z-folding. Start with Fold 1, and then set Fold 2. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To narrow [-] <-> [+] To widen | |||||
03 Tri-Fold-in Pos. Adj. Adjust the fold positions for tri-fold-in. Start with Fold 1, and then set Fold 2. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To narrow [-] <-> [+] To widen | |||||
04 Tri-Fold-out Pos. Adj. Adjust the fold positions for tri-fold-out. Start with Fold 1, and then set Fold 2. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To widen [-] <-> [+] To narrow Fold 2: To narrow [-] <-> [+] To widen | |||||
05 Double Parallel Pos. Adj. Adjust the fold positions for double parallel folding. Start with Fold 1, and then set Fold 2. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To narrow [-] <-> [+] To widen | |||||
06 Gate Position Adj. Adjust the fold position for gate folding. Start with Fold 1, and then set Fold 2 and Fold 3. | Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2, Fold 3: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To widen [-] <-> [+] To narrow Fold 3: To narrow [-] <-> [+] To widen | |||||
02 Finisher Adjustment (Large Capacity Stacker LS-506) This menu item is to be displayed and allowed on the machine mounted with Large Capacity Stacker LS-506. When three stackers are mounted, a setting can be configured for each stacker. | ||||||
03 Stacker Adjustment | ||||||
01 Paper Width Adjustment Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray. | Objects of adjustment: Stacker No.1, Stacker No.2, Stacker No.3 Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion | |||||
02 Paper Length Adjustment Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray. | Objects of adjustment: Stacker No.1, Stacker No.2, Stacker No.3 Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion | |||||
02 Finisher Adjustment (Saddle Stitcher SD-506) This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506. | ||||||
04 Saddle Stitcher Adjustment | ||||||
01 Fold Paper Width Adj. Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To reduce the misalignment [+] To reduce the distortion | |||||
02 Half-Fold Position Adj. Adjust the fold position determined by the half-folder. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To shorten the top face [+] To lengthen the top face | |||||
03 Staple Paper Width Adj. Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion | |||||
04 Staple Center Position Adjust the center position of staples determined by the saddle stitcher.
Prerequisite: Staple paper width adjustment is completed. | Adj. Range: -20~+20 1 step = 0.1 mm [-] To move closer to paper center (fold) [+] To move away from paper center (fold) | |||||
05 Staple Pitch Adjustment Adjust the staple pitch determined by the saddle stitcher. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -20~+20 1 step = 1.0 mm [-] To shorten [+] To lengthen | |||||
06 Trimming Adjustment Adjust the trimming width. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -400~+400 1 step = 0.1 mm [-] To narrow [+] To widen | |||||
07 Tri-Fold Position Adj. Adjust the folded positions in Tri-Fold mode. Start with Fold 1, and then set Fold 2. | Objects of adjustment: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed Fold 1, Fold 2: Adj. Range: -100~+100 1 step = 0.1 mm Fold 1: To widen [-] <-> [+] To narrow Fold 2: To narrow [-] <-> [+] To widen | |||||
08 Trimmer Receiver Adj. Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually. *Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative. | Objects of Adjustment: Trim Count Adjustment range: 700 times, 500 times, 300 times
Objects of Adjustment: Move Pitch Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm
Execute Compulsive Movement | |||||
02 Finisher Adjustment (Saddle Stitcher SD-513) This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-513. | ||||||
04 Saddle Stitcher Adjustment | ||||||
01 Fold Paper Width Adj. Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment. | Adjustment Range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm [-] To reduce the misalignment [+] To reduce the distortion | |||||
02 Fold Skew Adjustment Adjust the skew of the folding line. | Objects of Adjustment: Single Fold, Multi Fold Adjustment Range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm [-] To weaken [+] To strengthen | |||||
03 Half-Fold Position Adj. Adjust the folded position for half-fold. | Adjustment Range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm [-] To shorten the top face [+] To lengthen the top face | |||||
04 Tri-Fold Position Adj. Adjust the folded positions in Tri-Fold mode. Adjust Fold 1 and Fold 2 in this order.to | Adjustment Range: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed Fold 1: Offset for All Size, A4 short edge feed Adj. Range: -100~+90 1 step = 0.1 mm Fold 1: 8.5 11 short edge feed Adj. Range: -100~+30 1 step = 0.1 mm Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm [-]: To narrow [+]: To widen | |||||
05 Crease Position Adjustment Adjust the crease position. | ||||||
01 Half-Fold Crease Position Move the half-fold crease position. | Adjustment Range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To shorten [+] To lengthen | |||||
02 Tri-Fold Crease Position Move the tri-fold crease position. | Adjustment Range: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed Fold 1, Fold 2: Adj. Range: -20~+20 1 step = 0.1 mm [-] To shorten [+] To lengthen | |||||
03 PB Cover Crease Position Move the perfect binding cover crease position. | Adjustment Range: Crease Line 1, Crease Line 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To shorten [+] To lengthen | |||||
06 Staple Paper Width Adj. Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode. | Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion | |||||
07 Staple Center Position Adjust the center position of staples determined by the saddle stitcher. Prerequisite: Staple paper width adjustment is completed. | ||||||
01 2 Position Staple Adjust the center position for 2-position staple. | Adj. Range: -20~+20 1 step = 0.1 mm [-] To move rearward [+] To move frontward | |||||
02 4 Position Staple(Front 2) Adjust the center position at two locations on the front edge for 4-position staple. | Objects of adjustment: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -100~+100 1 step = 0.1 mm [-] To move rearward [+] To move frontward | |||||
03 4 Position Staple(Rear 2) Adjust the center position at two locations on the rear edge for 4-position staple. | Objects of adjustment: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -100~+100 1 step = 0.1 mm [-] To move rearward [+] To move frontward | |||||
08 Staple Pitch Adjustment Adjust the staple pitch determined by the saddle stitcher. | ||||||
01 2 Position Staple Adjust the pitch for 2-position staple. | Adjustment Range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 1.0 mm [-] To shorten [+] To lengthen | |||||
02 4 Position Staple(Front 2) Adjust the pitch at two locations on the front edge for 4-position staple. | Adjustment Range: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -10~+10 1 step = 1 mm [-] To shorten [+] To lengthen | |||||
03 4 Position Staple(Rear 2) Adjust the pitch at two locations on the rear edge for 4-position staple. | Adjustment Range: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -10~+10 1 step = 1 mm [-] To shorten [+] To lengthen | |||||
09 Staple Offset Adjustment Adjust the misalignment between the stapling positions and folding line. | Adj. Range: -10~+10 1 step = 0.1 mm [-] To move leftward [+]: To move rightward | |||||
10 Staple Tip Adjustment Change the staple leg shape. | Adj. Range: -9~+9 1 step = 1 msec [-]: To be round [+] To be flat | |||||
11 Flattening a Fold(Strength) Adjust the spine shape while changing the strength to form the book spine. | Adj. Range: -20~+20 1 step = 0.1 mm [-] To decrease the force [+] To increase the force | |||||
12 Flattening a Fold(Freq.) Adjust the number of roller reciprocation times to form the book spine. | Adj. Range: -5~+5 1 step = 1 [-] To decrease [+] To increase | |||||
13 Parallel Trimming Adjustment Adjust the levelness between the trimming line and cut edge. | Adjustment Range: Front, Rear Adj. Range: 0~+30 1 step = 0.1 mm [Up the numerical value] To widen [Down the numerical value] To narrow | |||||
14 Fore-edge Trimming Adj. Adjust the trimming width. The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly. | Adjustment Range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -400~+400 1 step = 0.1 mm [-] To narrow [+] To widen | |||||
15 2-Side Slitting Adjustment Adjust the 2-side slitting. | Adjustment Range: Front, Rear Adj. Range: -10~+10 1 step = 0.1 mm [-] To narrow [+] To widen | |||||
16 Trimmer Receiver Adj. Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually. *Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative. | Objects of Adjustment: Trim Count Adjustment range: 700 times, 500 times, 300 times
Objects of Adjustment: Move Pitch Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm
Execute Compulsive Movement | |||||
02 Finisher Adjustment (Perfect Binder PB-503) This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503. | ||||||
05 Perfect Binder Adjustment | ||||||
01 Sub Compile CD Width Adj. Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the dispersion | |||||
02 Clamp CD Width Adjustment Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the dispersion | |||||
03 Clamp FD Position Adj. Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the dispersion | |||||
04 Glue Start Position Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -128~+127 1 step = 0.1 mm [-] To increase [+] To decrease | |||||
05 Glue Finish Position Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: Ahead: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 short edge feed, A5 long edge feed, 8.5 11 long edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, 16K long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -128~+127 1 step = 0.1 mm [-] To decrease [+] To increase | |||||
06 Cover Lead Edge Adj. Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes. | Objects of adjustment: PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -128~+127 1 step = 0.1 mm [-] To move closer to the body [+] To move further from the body | |||||
07 Cover Trimming Adjustment Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance. | Objects of adjustment: Perfect Binder Tray, Except PB Tray Adj. Range: -128~+127 1 step = 0.1 mm [-] To narrow [+] To widen | |||||
08 Cover Up/Down CD Width Adj. Adjust the misalignment between the cover sheet and body. | Objects of adjustment: Perfect Binder Tray, Except PB Tray Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the misalignment | |||||
09 Spine Corner Forming Pos. Adjust the spine corners formed in cover sheets. | Objects of adjustment: Up/Down Forward Adj., Up/Down Rear Adj. Adj. Range: -128~+127 1 step = 0.1 mm [-] To convex [+] To concave | |||||
10 Temperature Adjustment Glue Tank -Low: Adjust the temperature to control the tank heater. (Temperature low) Down: viscosity increased (Temperature high) Up: viscosity decreased Glue Apply Roller: Adjust the temperature to control the roller heater. This also supports heating of the glue. (Temperature low) Down: viscosity increased (Temperature high) Up: viscosity decreased | Object of Adjustment: Glue Tank -Low Initial: 185°C Adj. Range: 180 °C~190 °C 1step = 1 °C Up: viscosity decreased Down: viscosity increased
Object of Adjustment: Glue Apply Roller Initial: 165°C Adj. Range: 160 °C~170 °C 1step = 1 °C Up: viscosity decreased Down: viscosity increased | |||||
02 Finisher Adjustment (Relay Unit RU-510) This menu item is to be displayed and become configurable when Relay Unit RU-510 is mounted. | ||||||
06: Relay Stacker (RU) Adjustment | ||||||
01 Paper Width Adjustment Adjust the alignment plate position in the crosswise direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510. For example, adjust a misalignment of punch holes in the crosswise direction. | Objects of adjustment: Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, A4 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 long edge feed, 9 11 long edge feed, Postcard, Custom(220~379 mm), Custom(100~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the randomness [+] To reduce the tilts | |||||
02 Paper Length Adjustment Adjust the alignment plate position in the paper feed direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510. For example, adjust a misalignment of punch holes in the crosswise direction. | Objects of adjustment: Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, A4 long edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 long edge feed, 9 11 long edge feed, Postcard, Custom(380~488 mm), Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the tilts | |||||
03 Process Adjustment | ||||||
01 Maximum Density Adjustment Adjust the maximum density. The machine will start the Gamma Automatic Adjustment after you change the maximum density. Be sure to perform Color Density Manual Control after changing the maximum density. | -10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5 | |||||
02 Max. Density Auto Adj. (RU) Chart printing and scanning are performed automatically, and the maximum density is adjusted automatically. The machine will start the Gamma Automatic Adjustment after you change the maximum density. Be sure to perform Color Density Manual Control after changing the maximum density. When this machine is equipped with Intelligent Quality Optimizer IQ-501, 02 Max. Density Auto Adj. is displayed. | - | |||||
04 Quality Adjustment Adjust the image quality. | ||||||
01 Highlight Adjustment Change the printer gamma curve to adjust the gradation and background density in highlights. | Screen1, Screen2, Stochastic Adj. Range: -128~+127 | |||||
02 Custom Screen Select screens to be used as Screen1, Screen2, and Stochastic, respectively. | Screen1: Dot210, Dot170, Dot140, Dot120, Dot105, Dot85 Screen2: Dot210, Dot170, Dot140, Dot120, Dot105, Dot85 Stochastic: FM1, FM2, FM3 | |||||
03 Controller Image Comp. Set Make this setting to smooth the jagged outlines of the text or line images. | Gradation Priority, Resolution Priority | |||||
04 Tone Curve for Each Tag Setting Select whether or not to allow tone curve adjustment for each tag (image, text/graphic). | Do Not Execute Adjustment, Execute Each Tag Adj. | |||||
05 Density Balance Adjustment | ||||||
01 Density Balance Chart Output Output the chart for density balance adjustment. | Objects of adjustment: Measure Spectrophotometer i1-iSisXL: 16-point measurement i1-Pro/i1-Pro2: 3-point measurement | |||||
02 Density Balance Data Reg/Del Load the colorimetric data, or manually register the data on the machine. | ||||||
05 Corner Staple(Back)Angle Select between diagonal and parallel stapling on the left corner. | Diagonal, Parallel | |||||
06 List/Counter Outputs User Management List, etc. Also, collectively save data on the USB flash drive connected to the USB port. | User Management List, Use Management List, Font Pattern List | |||||
07 Size Setting Specify the settings related to paper sizes of the paper placed in the Post Inserter. | ||||||
01 K Size Specify whether or not to use the K sizes such as 8K and 16K. | ON, OFF | |||||
02 A4 Tab Width Setting Select the tab width of A4-size tab paper. | 12.7 mm, 15.0 mm | |||||
08 Perfect Binder Setting This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503. | ||||||
01 Usable Paper Weight Select Set the paper weight available for body and cover paper, respectively, when using the perfect binder. | Usable Paper Weight Select Body: 62-74g/m2/18-19 lb Bond, 75-80g/m2/20-21 lb Bond, 81-91g/m2/22-24 lb Bond, 92-105g/m2/25-28 lb Bond Cover: 81-91g/m2/22-24 lb Bond, 92-105g/m2/25-28 lb Bond, 106-135g/m2/29-36 lb Bond, 136-162g/m2/37-43 lb Bond, 163-216g/m2/44-57 lb Bond Change Weight Unit g/m2, Duodecimo-kg, Octavo-kg, A Book-kg, B Book-kg, lb Bond, lb Index, lb Cover, lb Book, lb Bristol, lb Tag | |||||
02 Paper Count Limit for PB Specify the minimum and maximum numbers of sheets to be bound as a body, individually for each paper weight. | Weight: 62-74/18-19 Minimum Quantity: 10, 15, 20, 25 Maximum Quantity: 200, 250, 270, 300 75-80/20-21 Minimum Quantity: 10, 15, 20, 25 Maximum Quantity: 200, 250, 270, 300 81-91/22-24 Minimum Quantity: 10, 15, 20, 25 Maximum Quantity: 200, 250, 270, 300 92-105/25-28 Minimum Quantity: 10, 15, 20, 25 Maximum Quantity: 200, 250, 270, 300 Change Weight Unit: g/m2, Duodecimo-kg, Octavo-kg, A Book-kg, B Book-kg, lb Bond, lb Index, lb Cover, lb Book, lb Bristol, lb Tag | |||||
03 Unfitting Cover Stop Specify whether or not to stop the current job when the cover width is not suitable for the body size and spine thickness. | Temporary Stop, Not Temporary Stop | |||||
09 Operation Screen Customize | ||||||
01 Font Weight Setting Select the font weight for the screen. | Standard, Bold | |||||
02 Machine Function Key Setting Change the layout of function keys displayed on the MACHINE screen. | ― |
Register the name, extension number, and e-mail address of the administrator. The administrator name and extension number are always displayed in the upper-right corner of the UTILITY screen.
Administrator Name Setting (Up to 20 one-byte characters)
Extension No. Setting (Up to eight digits)
E-mail Address Setting (Up to 250 one-byte characters)
Specify whether or not to use the user authentication and account track functions. You can also specify or change the conditions in authentication.
Menu Item/Description | Setting value (: Default) | |
---|---|---|
1 General Settings Specify the authentication method of the user authentication and account track. | User Authentication: Authenticate, OFF, External Server Authentication, ON(MFP) Public User Access: ON (with Login), Restrict Account Track: ON, OFF Account Track Input Method: Account Name + Password, Password Only Synchronize User Authentication & Account Track: Synchronize, Do Not Synchronize When # of Jobs Reach Maximum: Stop Immediately, Stop After Print, Warning Only Number of users Counters Assigned: 1 to 999 (Default: 500) Ticket Hold Time Setting: 1 minute to 600 minutes (Default: 600) Count Sample Print: YES, NO | |
2 User Authentication Settings | ||
1 Administrative Settings Specify whether or not to display the user name list on the authentication screen. Also place the default function permissions on users for the authentication by an external server. | User Name List: ON, OFF Default Function Permission Print: Allow, Restrict User Box: Allow, Restrict | |
2 User Registration Add, change, or delete entries of users to be allowed in user authentication. | User No., User Name, Password, E-mail Address, Account Name, Max. Allowance Set, Function Permission (Print, User Box) | |
3 User Counter View or reset the count for each user. | ― | |
3 Account Track Settings | ||
1 Account Track Registration Change, add, or delete accounts to be tracked. | Account Name, Password, Max. Allowance Set, Function Permission (Print, User Box) | |
2 Account Track Counter View or reset the count for each account track. | ― | |
4 Print without Authentication Specify whether to make print function available to users without authentication. | Allow, Restrict | |
6 External Server Settings Register an external server, or edit or delete a registered server when External Server Authentication is selected as the Authentication Method. | ― | |
8 Authentication Device Settings | ||
1 General Settings Specify the type of IC card used for entering credentials. Also, specify the authentication method. | IC Card Type Setting: FeliCa, SSFC, FCF, FCF (Campus), Type A, Felica+TypeA, SSFC+TypeA, FCF+TypeA, FCF (Campus) +TypeA Operation Setting: IC Card Authentication, IC Card + Password Authentication | |
9 User/Account Common Setting Specify whether or not to display a logout confirmation dialog. | Logout confirmation Screen Display Setting: ON, OFF |
Menu Item/Description | Setting value (: Default) | |
---|---|---|
01 NIC Settings Configure various NIC settings. | TCP/IP Settings, HTTP Server Settings, FTP Settings, SMB Settings, LDAP Settings, E-mail Settings, SNMP Settings, Bonjour Setting*, TCP Socket Settings, WebDAV Settings, DPWS Settings, SSDP Settings, Detail Settings, IEEE802.1x Authentication Settings, IWS Settings, Remote Panel Settings, JSP Setting, Hot Folder Setting, AccurioPro Print Manager * To connect Bonjour in Macintosh, you need to configure TCP/IP setting in advance. | |
02 E-mail Initial Setting Configure initial settings for e-mail or perform transmitting/receiving test. | Use E-mail System: ON, OFF Time Zone: -1200 to +1200 (Default: 0) Trans (SMTP) Mail Server: Max. 128 characters (Default: 0.0.0.0) SMTP Port Number: 0 to 65535 (Default: 25) Trans Mail Server Timeout: 30 seconds to 5 minutes (Default: 5 minutes) New-arrival Check Interval: 1 to 60 minutes (Default: 0) Receive Mail Server: Max. 128 characters (Default: 0.0.0.0) Receive Mail Server Type: POP3, IMAP POP3/IMAP Port Number: 0 to 65535 (Default: POP3-110, IMAP-143) Receive Mail Account: Max. 64 characters Receive Mail Password: Max. 64 characters E-mail Address for Machine: Max. 128 characters POP (IMAP) before SMTP Auth.: ON, OFF SSL Encryption of SMTP: ON, OFF SSL Encryption of POP(IMAP): ON, OFF SMTP Authentication: ON, OFF SMTP Authentication User ID: Max. 64 characters SMTP Authentication Password: Max. 64 characters Test | |
03 http Communication Setting Configure the http communication settings. | Enable Proxy Server: ON, OFF Proxy Server Address: Max. 128 characters Proxy Server Port: 0 to 65535 (Default: 8080) Enable SSL: ON, OFF Enable Authentication: ON, OFF Authentication User Name: Max. 20 characters Authentication Password: Max. 20 characters | |
04 Quick Security Setting | ||
01 Quick IP Filtering Restrict access to the machine by means of IP address (IPv4/IPv6). | Filtering Method: No Filtering, Sync. IP Address, Sync. Subnet Mask IPv4 Access Range, IPv6 Access Range | |
02 Administrator Password Set an administrator password for the machine on which the administrator authentication function is set to OFF. The administrator authentication function is automatically turned ON. | Current Password, New Password, Input Confirmation For details about the default administrator password, refer to Safety Information. | |
03 Password Rules Setting Select whether or not to enable the password rules. | Password Rules Setting: Enable, Disable Set Minimum Password Length: 8 to 64 characters | |
04 WebUtilities Setting Select whether or not to use the functionality of Web Utilities. | ON, OFF | |
05 PSWC Setting Select whether or not to use the PageScope Web Connection function. | Enable, Disable | |
06 Security Warning Display Select whether or not to display the Security Setting Warning screen. | Display, Not Display |
Menu Item/Description | Setting value (: Default) |
---|---|
One Shot Message Indication Time Select the time span to display a shot message in the message area of the touch panel. | 3 seconds, 5 seconds |
Offset by Job Unit Specify whether or not to offset the output sheets by job. Also specify the number of jobs to be offset when selecting ON for this function. | ON, OFF (Selecting ON: Offset Job Number) |
Continuation Print Specify whether or not to output multiple reserve jobs in succession without stopping the machine at a job break. | Printer ON, Printer OFF |
Dark Tone Control In order to adjust the quality of the output image, select whether to automatically decrease the output speed (Quality), prioritize the output speed, or disable the ability to control the tone. | OFF, Quality, Performance |
Icon Display for Dark Tone Control Select whether or not to display the Dark Tone icon while the Dark Tone Control function is enabled. This function is available only when Quality or Performance is selected at Dark Tone Control. | ON, OFF |
Dash Length(Page Stamp) Select the length of the dash to be used in a style of Page No. in Stamp. | Long, Short |
Center Crop Mark Trim Margin Specify the space between the center crop mark and image area (center crop mark trim margin). | 0.0 mm to 20.0 mm (Default: 1.0) |
Schedule Cross Axis Unit (Default) Select the unit of horizontal axis on the Schedule screen. | Timetable, Time Frame (m), Sheet Volume |
Hold Job Status after Output (Default) Select the default value to delete or save the data of hold job after outputting. | Delete, Save |
Hold Job Direct Output (Default) Select the default for the Direct Output check box under the Hold Job screen. | ON, OFF |
Offset Output Mode Specify how to offset the output sets. | Change Out Pos., Stop Print, Change Out Pos. + Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3), Partition Paper (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11, PI1, PI2, PI-PFU1, PI-PFU2, PI-PFU3) |
Needless Tab Paper Exit Specify whether or not to automatically discharge the oddments of tabbed sheets loaded in a tray as a set. | ON, OFF |
Remaining Memory (Measurement Unit) Select the unit of displaying the remaining memory. | %, GB |
Remaining Memory (Warning) Select the percentage at which to give warning when the remaining memory is low. | 5% or Less, 10% or Less |
[Proof Copy] 1 Set/1st Sheet Selection If it is turned ON, the confirmation window is opened and you are asked to output one confirmation copy or to output only its first page when the Proof Copy is pressed. | ON, OFF |
Temp. Down/Up Control before Print Select whether to rotate the fusing roller before printing starts, in order to print at the appropriate temperature. | ON, OFF |
Both Sides Rotate/Skew If Disable is selected, the Rotate/Skew adjustment does not become available and does not function. | Enable, Invalid |
Stop when Water Tank Near Empty Select whether to temporarily stop a job when the humidifier tank runs low on water. | Temporary Stop, Not Temporary Stop |
Auto Image Adjustment Deviation Check Select whether to automatically check a deviation. If you select ON, enter the specified value of a deviation. This option is displayed when Intelligent Quality Optimizer IQ-501 is mounted on the machine. | ON (ON: 0.5 mm to 10.0 mm), OFF |
Operation after Deviation Detected Select an operation to be performed when a deviation is detected. When Continue Output is selected, specify the paper tray to feed partition paper and the number of detection times. This option is displayed when Intelligent Quality Optimizer IQ-501 is mounted on the machine. | Stop, Continue Output, Partition Paper Tray at Deviation (Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11), Detection Count (2 to 10 times) |
Select Chart Type (Auto Image Adj.) Select an automatic image adjustment chart for each paper weight. The unit of weight can be switched. This option is displayed when Intelligent Quality Optimizer IQ-501 is mounted on the machine. | 40-49g/m2/10-13 lb Bond: Type1, Type2 50-54g/m2/14-15 lb Bond: Type1, Type2 55-61g/m2/16-17 lb Bond: Type1, Type2 62-74g/m2/18-19 lb Bond: Type1, Type2 75-80g/m2/20-21 lb Bond: Type1, Type2 81-91g/m2/22-24 lb Bond: Type1, Type2 92-105g/m2/25-28 lb Bond: Type1, Type2 106-135g/m2/29-36 lb Bond: Type1, Type2 136-162g/m2/37-43 lb Bond: Type1, Type2 163-216g/m2/44-57 lb Bond: Type1, Type2 217-256g/m2/58-68 lb Bond: Type1, Type2 257-300g/m2/69-81 lb Bond: Type1, Type2 301-350g/m2/82-93 lb Bond: Type1, Type2 Change Unit |
Menu Item/Description | Setting value (: Default) | |
---|---|---|
1 OpenAPI Settings Set the OpenAPI information. | Access Setting: Allow, Restrict SSL/Port Settings Authentication: ON, OFF, Login Name, Password Proxy Settings: Port Number (HTTP) (Default: 8080), Port Number (HTTPS) (Default: 8080), Port Number (FTP) (Default: 21), Host Address, User Name, Password | |
2 Call Remote Center Press Start to call your service representative via CS Remote Care. | Start | |
3 Browser Screen Setting | ||
OpenAPI/IWS Appli. Size Set. Specify the screen size of the OpenAPI or IWS application. | Small Size, Large Size | |
Screen Saver Size Setting Specify the screen size of the screen saver. | Small Size, Large Size |
Menu Item/Description | Setting value (: Default) | ||
---|---|---|---|
01 Administrator Password Change the administrator password. | For details about the default administrator password, refer to Safety Information. | ||
02 HDD Management Setting | |||
01 HDD Lock Password Change the HDD lock password. | ― | ||
02 Delete Temp. Data Setting Specify whether or not to overwrite the temporary image data on the memory. Select the erase mode to overwrite and delete data. | Setting Switch: ON, OFF Erase Mode: Mode 1, Mode 2 | ||
03 Delete All Data Setting Select the desired erase mode to delete all the data on the HDD or the non-volatile memory of this machine. Also execute deleting all the data. | Erase Mode: Mode 1, Mode 2, Mode 3, Mode 4, Mode 5, Mode 6, Mode 7, Mode 8 Execute Deletion | ||
04 Delete Hold Job Use this function to delete hold jobs. | ― | ||
05 Delete HDD Job Use this function to delete the jobs saved on the HDD. | ― | ||
06 Delete Secure Job Use this function to delete secure jobs from the security job box. | ― | ||
07 HDD Restore/Backup Make a backup of, or restore the HDD. | |||
01 HDD ALL Backup Create a backup of all the hold job and HDD job saved on the HDD onto an external storage medium connected to the USB port. | Start | ||
02 HDD ALL Restore Restore the backup data created using HDD ALL Backup. | Start | ||
03 HDD BOX Backup Create a backup of the jobs in the backup folder of the HDD job onto an external medium connected to the USB port. | Start | ||
04 HDD BOX Restore Restore the backup data created using HDD BOX Backup. | Start | ||
05 Controller Backup Create a backup of setting data saved on the Image Controller onto an external storage medium connected to the USB port. | Start | ||
06 Controller Restore Restore the backup data created using Controller Backup. | Start | ||
08 HDD Encryption Setting Set whether or not to save all jobs saved on the HDD upon encrypting them, and set the encryption password. | ON, OFF | ||
09 HDD Job Auto Delete Period Set the time when the jobs on hold are automatically deleted. | Not Delete, 12 hours, 1 day, 2 days, 3 days, 7 days, 30 days | ||
03 Enhanced Security Mode Specify whether or not to activate the Enhanced Security mode. | ON, OFF | ||
04 Service Login Allow Setting Restrict usage of the service mode by the customer engineer. | Allow, Restrict | ||
05 Audit Log Setting | |||
01 Audit Log Address Server Setting Specify the destination to transmit audit logs to. | Audit Log Trans.: ON, OFF Host Address, File Path, Login Name, Password, Port Number Poxy: ON, OFF | ||
02 Audit Log Manual Trans. Manually transmit audit logs. | Transmission | ||
06 Run Self-diagnostic Test Test whether there is a problem with the security function. | Firmware Diagnosis, Device Diagnosis | ||
07 Acquire Image Log(AutoImage) Specify whether your service representative can acquire the image saved when Auto Image Adjustment is executed. | Restrict, Allow |
Register or check the restriction code in Restriction Code Settings.
Index
Vendor
Application
You can view the firmware version of the machine or optional units mounted in the machine.
You can rewrite the ROM (programs and data) included in the flash drive or SSD of each unit. Download ROM files from the USB flash drive connected to the main body, and rewrite them.
Menu Item/Description | Setting value (: Default) | |||
---|---|---|---|---|
01 Software Switch Setting Specify the corresponding switch number in order to address the problems or requirements described in the List of Software Switch Setting. | On, Off | |||
02 Default Machine Setting Returns Software Switch Setting and Controller on the MACHINE screen to the factory defaults. | Start | |||
03 Secure Print Only Setting | Off, On |
Use this function to check that the keys displayed on the screen and the touch sensor are properly aligned, if the machine does not respond to the press on the touch panel properly.
Menu Item/Description | Setting value (: Default) |
---|---|
01 Quick IP Filtering Restrict access to the machine by means of IP address (IPv4/IPv6). | Filtering Method: No Filtering, Sync. IP Address, Sync. Subnet Mask IPv4 Access Range, IPv6 Access Range |
02 Administrator Password Set an administrator password for the machine on which the administrator authentication function is set to OFF. The administrator authentication function is automatically turned ON. | Current Password, New Password, Input Confirmation For details about the default administrator password, refer to Safety Information. |
03 Password Rules Setting Select whether or not to enable the password rules. | Password Rules Setting: Enable, Disable Set Minimum Password Length: 8 to 64 characters |
04 WebUtilities Setting Select whether or not to use the functionality of Web Utilities. | ON, OFF |
05 PSWC Setting Select whether or not to use the PageScope Web Connection function. | Enable, Disable |
06 Security Warning Display Select whether or not to display the Security Setting Warning screen. | Display, Not Display |
Starts the remote operation for the control panel of this machine.
This setting is displayed only when the remote panel setting is configured by the administrator. For details about the remote panel setting, refer to [Remote Panel Settings] (when using the control panel for setting) or [Remote Panel Client Settings] (when using PageScope Web Connection for setting).